PARAMETER

SPECIFICATION

Product form

Vertical

Heating method

Electric heating

Power

18.0KVA

Power

AC380V, 50Hz

Dimensions

(L × W × H): 1360x810x1580mm

Liner size

 (Diameter × Depth): 500 × 1000mm

Capacity

200L

Shelves

Two trays

Weight

360kg

Temperature display

 7” LCD Touch screen

Design Pressure

 0.3MPa

Working pressure

-0.8MPa～0.21MPa

Design temperature

150 ℃

Working temperature

121 ℃ / 134 ℃

Number of pulses

3 times (0~400 times adjustable)

Sterilization time

0 ～ 9999 seconds

Drying time

0 ～ 9999 seconds

Safety valve in sterilization chamber

Open ≧ 0.25Mpa, close ≦ 0.24Mpa

Pulsation amplitude

-80.0KPA~150KPA

Water source of evaporator

softened or purified water, water temperature ≤45 ℃, water pressure 0 ～ 0.05 Mpa

Water source of vacuum pump

Tap water (hardness should not be too high), water pressure 0.15Mpa ~ 0.30Mpa

Air Discharge

＞ 99 ﹪ (Pulsation times more than 3 times)

Vacuum Drying

Avoid humidifying the disinfection package after disinfection

Pulse exhaust

Positive pressure dynamic pulse exhaust to completely eliminate cold air in the sterilization room and ensure steam saturation

Working procedures

Water injection, preheating, pulse vacuum, sterilization, drying and dormancy are automatically completed

Microcomputer control technology

The sterilizer uses microprocessor intelligent control, man-machine interface, easy to operate, safe and reliable. The parameters and status during operation are displayed dynamically through the digital screen. The equipment works abnormally and automatically detects and alarms after sterilization is completed, the system automatically prompts and is accompanied by a buzzer warning sound

Locking device

Before the start of the sterilization cycle, the interlocking device is not locked after the door is closed, and the door can be closed and opened repeatedly. Only when the door is closed in place, the sterilizer can start to run. During the operation, the sterilizer door should not be opened. After the start of the cycle operation, if a fault or fault indication occurs, the sterilization chamber is not completely released, and when the interlock device should be locked, the sterilizer door should not be opened

Pulsation mode

Microcomputer control automatically selects the number of pulsations according to the site conditions to ensure the coordination of temperature and pressure

Vacuum mode

Three pre-vacuums to ensure faster heating and more complete sterilization

Safety valve

When the pressure of the sterilizer reaches 240kPa ± 5kPa, the safety valve will automatically open to relieve the pressure

Over pressure protection program

When the pressure in the sterilization chamber reaches 220 ± 5kPakPa, there is a prompt sound and the pressure can be automatically released

Air Leakage

When the sterilizer is tested in various stages, the pressure increase rate should not be greater than 0.13kPa / min

Dynamic pressure in sterilization chamber

The pressure change in any 2s interval during the sterilizer cycle should not exceed 1000kPa / min

Vacuum pump

The water ring vacuum pump is used, which is simple and convenient, the vacuum rate is fast, and the service life is long. Ensure that the vacuum can reach -80kpa

Pressure Sensor

The built-in pressure sensor automatically detects the pressure in the cavity

Temperature Sensor

The built-in temperature sensor automatically detects the temperature in the cavity to ensure that the cavity is kept within an accurate range of ± 3 ℃ of the operating temperature

Sterilization Mode

Sterilization mode for solid equipment, dressing packaging, rubber products, BD test, high pressure, etc

Automatic drying

Powerful vacuum drying, suitable for different items drying needs; the remaining humidity of the equipment is <0.2%

Seal structure

The sealing ring is made of silicone, and the designed service life is 2 years (1200 times) without aging and deformation

Foot wheel

Yes

Alarm system

High and low temperature alarm system